You don’t want your house to have the smell of a sewer drifting through it, but this can sometimes happen to even the cleanest house because of troubles with the plumbing. If your house has terrible odors making daily life unpleasant, you’ll want to know the source and have it corrected.
We’re going to look at common causes of foul smells from plumbing in Peoria, AZ. This can help you know what to do about them. Our plumbers are ready to help make your house smell fresh again, and we have 24-hour emergency service to correct any plumbing disaster you run into.
ONE: Problems with the sewer line
We’ll start with a worst-case scenario, but unfortunately a common trouble for residential plumbing systems. The sewer odors in your house may actually be emanating from the sewer line itself. When the sewer line is in regular working shape, it moves wastewater from the drains in your house out to the municipal sewer line without you noticing. But if the line develops breaches, clogs, or root infiltration, it will begin to push sewer gas the wrong direction through the plumbing. The odors are a warning: unless the sewer line issue is addressed, actual sewage backup will eventually occur. You need professional plumbers on the job ASAP!
TWO: Blocked drain vents
Drain vents are the pipes that allow sewer gas to escape up through outlets in the top of the house. This prevents a buildup of pressure between the sewer line and the drains. If these escape-route pipes become clogged, they will push gas up through the drains.
THREE: The dried p-trap
Here’s an easy one you can fix yourself. Can you track the bad odors to a single drain? If so, is this a drain that hasn’t been used in a few weeks? Then the trouble is that the p-trap—the curved section of pipe that holds a barrier of water—has dried out and sewer gas is rising through it. Simply run water down the drain for a minute or so to restore the p-trap’s water barrier.
FOUR: The dirty garbage disposal
When you consider how much food waste goes down your kitchen’s garbage disposal on a regular basis, it’s surprising that it doesn’t develop odors more often. But disposals are designed to rapidly move ground-up waste into drain lines and leave little residue. The residue can build up over time, and if the disposal is malfunctioning it can cause a large accumulation of rotten food. The disposal may need to be cleaned, although for older units (more than 10 years) it may be better to replace it.
FIVE: Bacteria
This an issue you may encounter from the shower drain. Bacteria can develop within a substance called “biofilm” that grows inside shower drains because of soap, shampoo, and other body-cleaning products accumulating. It can affect other drains as well, and the best approach to solving this problem is with drain cleaning. No, don’t use chemical drain cleaners! They won’t solve the issue. It takes professionals drain cleaning to wipe out a biofilm buildup in drains.
Trust The Trusted Plumber! Call us for emergency plumbing repair in Glendale, AZ and the surrounding areas.
The water heater is an essential appliance that does its important job faithfully, day after day, without much notice – until it’s no longer as dependable as it used to be. Yet determining the time when repair isn’t cost-effective or when to be proactive and replace it before your water heater conks out completely is easier said than done. Fortunately, there are telltale signs to look for and factor into your decision to buy a new unit.
While ourstate-certified master plumbers atAdams and Son Plumbing have extensive experience answering emergency calls about water heaters that suddenly expire and/or empty their contents all over the utility room floor, we’d rather spare Central Florida homeowners the stress. Here is what you need to know to avoid trouble and extra expense.
How to Tell Before Trouble Starts – How Old is Your Water Heater?
The average lifespan of a typical electric storage tank water heater is 10 to 15 years; that of a gas storage tank water heater is eight to 12 years. Tankless models can last 20 to 30 years.
But what if you don’t know your water heater’s age – which is possible if it was in place when you bought your house? For a tank model, one sure way is to check its serial number. This is typically located on the manufacturer’s sticker on the upper half of the tank. But as if to make things complicated for the average homeowner, it’s listed in code. Decoding the serial number can be tricky, as they vary by manufacturer.Hot Water Solutions provides ahelpful guide to make sense of it all.
When you know your water heater is nearing the end of its useful life, you can plan accordingly. You’ll have time to compare and choose the model best suited for the size of your house and the amount of hot water your family uses on average. You may even be able to switch from tank to tankless. This is a far better situation than having to replace your unit during an emergency, when you’ll need to take whatever is available.
Has Trouble Started? Here are the Signs to Look for!
While a leak is the most obvious sign, it isn’t really a sign – it’s the aforementioned emergency. Moisture or a puddle around the unit’s base means you don’t have the luxury of shopping around. Replace it immediately! Leaks are usually caused by a build-up of pressure inside the tank. This occurs when the water pressure or temperature is too high, or when the relief valve isn’t working properly. Neglecting a leak can lead to the tank exploding. Need we say more?
One of the first indications of trouble could be a sudden increase in your utility bill. If there is no other cause (such as a pipe leak), your unit could be expending extra energy to provide the same amount of hot water. Should this be the case, look for the other following signs:
Rusty or cloudy water – Water discoloration is a definite sign your unit is underperforming. Rust-colored water, or water with a metallic odor, can mean a few things. Either the sacrificial anode rod needs to be replaced or the tank itself is beginning to rust, which is often due to corrosion of the steel lining. A rotten egg odor indicates the growth of bacteria in the tank. A corroded tank must be replaced as soon as possible. Cloudy water often indicates a sediment buildup inside the tank, and if the water remains cold, a heating element may be broken. If this is the case, the heating element can be replaced, but be on notice that replacement time may be near.
Rusty pipes – Rust could also come from the pipe that brings water to your faucets. Regardless of the source, you need to address the problem urgently because it is a sanitation issue. To check whether the problem is with your water heater or your pipes, you can open your hot water tap and let it run for some time. If the rusty water continues to flow by the third bucket load, it means the rust problem is in the water heater.
Rusty valve/inlet – If you see rust around the water inlet or pressure relief valve, it means there is rust present in the tank. It also means it’s time to replace the unit as soon as possible.
Knocking noises – If you hear loud noises coming from your water heater, it means there is sediment buildup inside the tank. When the sediment hardens, it can start moving around the tank, causing those unwanted sounds.
Once there is sediment buildup in your water heater, it starts consuming more energy to heat the same amount of water. The knocking sound is another indication that your water heater has lived its life of faithful service. If you want to increase the life of your water heater, flush and clean your tank periodically (or call a plumber to do the job).
Cold water – If the water heater dispenses cold water instead, a tripped limit switch, misadjusted thermostat or broken heating element could be the culprit. First, check the water heater’s circuit breaker in the service panel to make sure it hasn’t tripped. If the breaker has tripped, switch it off, then switch it back on again. If the heater’s breaker did not trip (it is still on), try to reset the high-temperature limit on the heater. Our blog post – “Why Does My Hot Water Never Last Long Enough?” – offers troubleshooting tips, as well as how to tell when it’s time tocall a plumber.
Another reason could be that the water heater is too small to provide enough hot water for your household’s needs. If the size of your household has increased recently, you may need a larger capacity tank.
Repair or Replace? Which Type of Water Heater is Best for Your Home?
There are occasions when your water heater can be repaired. Some of the replaceable parts include the burner assembly, heating elements, thermostats, valves, thermocouples, motors and igniters.
You can consider getting your storage tank water heater repaired if it is less than 10 years old and a replaceable part fails. However, if it is more than 10 years old, you haven’t maintained it properly, or you see any of the signs mentioned above, you should consider replacement. Repairs are generally not cost-effective once the unit reaches the average limit of its useful life.
As a water heater is an important investment, you need to considerwhich type is best for your home based upon cost, efficiency and longevity. Traditional storage tank units are still the most popular. However, tankless water heaters are quickly increasing in popularity.
Tankless water heaters use high-powered burners to rapidly heat water as it runs through a heat exchanger and deliver it directly to your faucets or shower without storing it in a tank, providing hot water on-demand. Tankless water heaters are powered with electricity or gas. One of their main advantages is energy efficiency, as they were found to be 22% more energy efficient on average than gas-fueled storage-tank models in tests conducted by Consumer Reports.
Storage tank water heaters are more common. They have an insulated tank that can hold 30 to 50 gallons of water. These water heaters run on gas or electricity. Natural gas storage tank water heaters are more energy efficient (almost 50%) than their electric counterparts. Natural gas storage tank water heaters are slightly more expensive than electric models. These water heaters also have a temperature and pressure release valve that opens up when the pressure or temperature increases beyond the specified limit.
Compared with storage tank water heaters, homeowners who have tankless water heaters and use less than 41 gallons or less of water per day can save anywhere between 24% to 34% in energy costs. If you use around 86 gallons of hot water every day, you can still save 8 to 14% on energy costs. Also, compared to storage tank units, tankless water heaters are less prone to corrosion. Another plus: The lack of a tankeliminates the possibility of a catastrophic water leak that can damage flooring, furniture, etc.
According to U.S. Department of Energy estimates, in comparison to a traditional gas-powered storage tank water heater, a gas-powered tankless water heater can save an average of $108 in energy costs every year. An electric tankless model can save an average of $44 every year over their traditional tank counterpart.
Tankless water heaters can save you money in the longer run, have a longer lifespan, don’t occupy too much space, and can instantly provide you hot water. But this type is more costly than storage tank water heaters, installation is more complex and expensive, and it might not be able to keep up with demand if you are doing numerous chores requiring hot water at the same time.
Storage tank water heaters are not all that costly, and their maintenance and repairs are less expensive. But storage tank water heaters are less energy-efficient, occupy more space, can store only a limited amount of hot water and have a lower lifespan as compared to a tankless model.
The Take-Home Message
Now that you know how to determine whether to repair or replace – as well as the pros and cons of storage tank and tankless water heaters –you will (hopefully) be able to select your next unit based on the factors and features you consider important, rather than under duress.
Whether your water heater needs repair, or you’re ready to replace it, call us!Adams and Son Plumbing is a family-owned business with over 50 years in plumbing service. A state-certified plumbing contractor, we have over three generations of master plumbing experience. Contact us to learn more and schedule a service appointment.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Learning how to install a bidet attachment is a fantastic way to save money. Not only do you save money by installing it yourself, but modern bidet attachments use very little water, so they remain cost-effective to use.
Furthermore, you may never have to repurchase toilet paper, and if you have a big family, you know all too well how much you go through every week.
The bidet found popularity in the 1600s, especially in Europe. However, the refreshing cleaning device failed to ignite bottoms in America, though our growing awareness of the environment may change that.
So, if you want a hyper-clean bottom and would like to save money simultaneously, you may wish to learn how to install a bidet attachment.
How to Install a Bidet Attachment
Unlike a free-standing bidet, which can be challenging to fit, a bidet attachment is a job you can complete within a couple of hours on the weekend.
Most bidet attachment kits supply the main elements needed to complete the job, though you may also need a few essential tools.
A bidet attachment fits the existing seat. After fitting the T-valve adaptor, you re-attach the water supply and connect the hose to the bidet attachment and T-adaptor. Once you place the toilet seat back in position, you can start to use the bidet for a deep-down clean!
Some basic equipment
Don’t feel intimidated when you learn how to install a bidet attachment because they come with full instructions. Furthermore, the kit supplies most of the parts you need to complete the job.
The kit arrives with a 7/8 inch connection T-adaptor, a toilet bidet seat mounting attachment, and a length of flexible water hose. However, you might need to stock up on some basic bits and pieces to complete the job successfully.
What you need
A good quality wrench proves vital to complete the job. Ensure you use the appropriate size as forcing the issue with an ill-fitting wrench may damage the system and cause water leaks.
Plumbers tape seals the water connections and provides an excellent seal. If you don’t use the tape, you may find that water drips from the pipes and valves, and then you have to start all over again.
A range of screwdrivers helps you to fix the bidet attachment and toilet seat into position. Don’t use old battered screwdrivers because you run the risk of ruining the heads of the screws, and the last thing you want is a loose loo seat!
A bidet attachment consists of a fixture that goes at the toilet seat’s backside and contains a nozzle facing your rear end.
Usually, a small control unit allows you to turn the device on and control water flow. Some units use dual nozzle systems for front and back use, while others will enable the user to control the water’s direction.
How does a bidet work?
A bidet forms a hygienic alternative to using toilet paper. It works by directing a stream of water through nozzles to clean your nether regions after contemplating on the loo.
The bidet uses water directly from the main water supply. Consequently, the water remains clean and sanitary. Furthermore, most bidets use self-cleaning nozzles, but it’s a good idea to clean them when you undertake your regular toilet cleaning chores.
From a hygienic perspective, a bidet provides you with a deep-down clean. Toilet paper tends to extend the problem of waste rather than eradicate it, leading to unhealthy and unsanitary conditions.
However, a bidet uses water to remove the offending waste so that it doesn’t come into contact with any other parts of your body.
The benefits of using a bidet attachment
When you learn how to install a bidet attachment, you may discover some fantastic benefits of using the system.
When you use a bidet, you don’t need to use toilet paper. Consequently, the process proves environmentally friendly because you’re not flushing copious amounts of paper into the drainage system.
Furthermore, the risk of blockages, clogging, and the resulting repairs lessen significantly when you use a bidet.
Using a bidet is healthy and hygienic when compared to using toilet paper. It leaves your behind feeling cleaner, fresher, and healthier.
Some people find toilet paper uncomfortable to use and may develop a rash or sore skin from using paper. When you consider toilet paper, it consists of nothing more than dry paper, which may irritate the skin. Anyone who suffers from irritable bowel syndrome knows all too well the pitfalls of constant toilet paper usage.
Washing your behind with water is a gentler alternative to rubbing the sensitive area with dry paper!
A bidet is gentle on the skin, and the flush of water after using the loo leaves you feeling refreshed and squeaky clean.
Save money
Money is tighter than ever, given our current worldwide circumstances, so using a bidet cuts out the toilet paper bill. Furthermore, a bidet attachment uses less water than a conventional stand-alone bidet, so it may save you money on your water bills.
Stand-alone bidet systems cost more to buy and install than a bidet attachment. Imagine all that expensive plumbing and groundwork to install a bidet. For many of us, such a cost is out of the question.
However, when you learn how to install a bidet attachment, it is easy to achieve and cost-effective.
How to Install a Bidet Attachment Explained
We understand that using a bidet is cost-effective and leads to a healthy, clean derriere.
When you buy a bidet attachment, it arrives with detailed instructions to guide you through the process, but the unit’s fitting proves more manageable than you may think.
Step 1
Begin by shutting off the water supply for the toilet and flush the toilet to empty it. The last thing you want is toilet water gushing all over you as you work!
Step 2
Use your spanners to disconnect the hose attachment from the bottom of the toilet tank.
However, take care not to strip the connections when unscrewing them and don’t apply too much force. Make sure to use the appropriately sized spanner and lubricate the area with a bit of WD40 if necessary.
Step 3
Use good quality screwdrivers to remove the toilet seat. Be careful not to damage the screw heads as you need to replace them afterward. Ensure the head of your screwdriver remains true to shape to avoid ruining the screws.
Before you move on, wipe the area down to ensure everything stays clean and free from water.
Step 4
It’s time to fit the T-vale adaptor to the bottom of the toilet bowl. Take your time with this step and use your wrench gently because you don’t want to overtighten the screw and risk threading them. Apply a little of the plumber’s tape to the screws to achieve a good seal.
When you re-attach the water hose from the water hook up to the T-adaptor’s bottom, you may need to use a washer or additional plumber’s tape to prevent leakage. Take your time and use the spanner gently without forcing the bolts into place.
Step 6
Take the flexible hose supplied with the kit and attach it to the T-adapter. You may use a little plumber’s tape on the joints to ensure a successful seal but take care not to overtighten the fittings. Attach the other end of the hose to the bidet water attachment and set it aside.
Step 7
You may find a piece of rubber inside your kit, which you attach to the underside of the seat mounting. Use the grooves on the underside as a guide for the correct placement of the rubber.
Now, line the unit up with the toilet seat screw holes and lay the bidet flat on top of the toilet.
Step 8
Place the toilet seat on top of the bidet attachment and ensure the holes line up before inserting the toilet screws. Take time to ensure perfect alignment and tighten the fixings once you feel satisfied with the positioning.
You need to ensure the fixings stay tight. If not, you may find yourself sliding off the toilet when you use it, and that’s not a good look!
Step 9
Now it’s time for the big reveal! Turn on the water. At this stage, ruin your fingers around each joint to ensure no water leakage. If you find water dripping from a joint, you may need to tighten the fixing further to form a tight seal.
A job well done
Learning how to install a bidet attachment is easy when you follow each step and take your time. Don’t rush the job, and ensure you use good quality tools as you work. The plumber’s tape is an invaluable tool because it helps seal the joints to lessen leakage risk.
Troubleshooting
Once you complete the job, it’s time to run the system through its paces. However, if you come across any issues, you must attend to them immediately.
Leaks
If you discover any leaks, you may need to tighten the joints. In some cases, you may need to turn the water off and re-do the offending joint, primarily if you haven’t used plumber’s tape. In a worst-case scenario, you may need to install washers into the joints to prevent leaks.
Water pressure
If the water pressure proves too high when you use the bidet, you’ll know all about it! Consequently, if you don’t want a bum power wash, you may need to adjust the water pressure.
The controls on the unit help you to adjust the strength of the water jet. Alternatively, you can adjust the water on/off connection to half to reduce the flow’s power.
How to Install a Bidet Attachment Explored
You don’t have to learn complex plumbing to know how to install a bidet attachment. Most units arrive with the items needed to fit your new bidet, and with some essential tools at hand, you can make short work of the job.
A bidet offers a hygienic, money-saving alternative to using toilet paper. If you suffer from bowel conditions, irritable skin, or eczema, using toilet paper may be a challenge and exacerbate the condition.
Consequently, using a bidet may help to alleviate these ailments and make using the loo a better experience.
Make sure to have some plumber’s tape, a set of screwdrivers, and wrenches at hand. Furthermore, you must always follow the manufacturer’s instructions when learning how to install a bidet attachment.
You can adjust the water pressure for a comfortable experience and bask in the knowledge that you fitted the bidet yourself!
Have you ever tried a bidet? Did it change your outlook on bathroom hygiene? Share your experience in the comments below.
Sean Kerr lives in Cardiff, Wales, and is a published author with over 10 novels to his name so far and still counting. As well as writing his next bestseller, Sean also runs a successful jewelry-making business and sells his creations online.
Have you ever found leaks in your home? Have you ever dealt with a flooded basement? If you have, I can assure you that it’s Toronto’s sewer system flooding over.
Over the years, Toronto has faced severe weather conditions. There have been up to $80 million worth of property damages due to rainfall and storms. A backwater valve installation is the best solution.
You may be wondering why you need a backwater valve. This is a very useful contraption that closes off any sewer water from coming back into your home. The backwater valve blocks the sewage of the city from invading your basement.
The best safety measure you could take for your family and home is to install a backwater valve as soon as possible.
Here are some signs you need a backwater valve installation.
1. You Have a Basement
If you have a floor under street level, you’re bound to deal with flooding. Whenever there are heavy rainfall, the city sewer system floods, pushing back sewage into your home’s sewer system.
Many older homes with basements don’t have a backwater valve installed. Not only are these basements prone to flooding, but they are prone to sewage.
A basement flooding has serious complications. The moisture of the sewage can seep into your walls and break down the structure of your home.
There is also a health concern with the countless number of bacteria, mold, and fungus found in the sewer water. These can negatively impact your respiratory health.
You should install a backwater valve for the safety of your home and your health.
2. It Rains in Your Area
Have you ever been through a rainstorm, or dealt with melting snow?
With the effects of global warming, the weather in Toronto has become harsher over the years.
Many environmental factors can ruin your property and your home’s water supply. Heavy rainfall, snowfall, and melting snow can cause flooding of your drains.
Water damage due to weather is the leading cause of an increase in property maintenance costs.
Since climate change is worsening every year, you should be prepared for the worst weather conditions.
3. You Have Cracks in Your Walls
A lot of older houses wear down over the years.
If your home has gaps or cracks in the walls, these shouldn’t be ignored.
Gaps and cracks are indicators of poor structure and can cause irreparable damages to your home when it rains. Any signs of moisture in your basement can penetrate your walls and cause mildew and mold growth.
It’s best to install a backwater valve to prevent any moisture from accumulating in your basement. If your house has cracks and spots, take precautions to protect them from degradation.
4. Your Neighbors Have Backwater Valves
Assume that your neighbors have backwater valves installed under their homes.
If your neighbors are protecting their homes from excess sewer water, where is all of that water going? It’s going straight to your house.
A backwater valve installation is the only way you can prevent your neighbors’ sewage and the city’s sewage, from damaging your home every time it rains.
5. Flood Damages Are Expensive
Although much of your home’s water damage is from the city’s sewer, most of it isn’t covered by Toronto.
Even most home insurance companies don’t take care of water damage costs.
This means that whenever the city sewage comes back into your drain, you’ll have to pay for the repairs out of your pocket.
The only way to avoid spending thousands of dollars on rebuilding your basement is to invest in a backwater valve installation.
6. The City Covers Your Backwater Valve Installation Price
Yup, you read that correctly. The city of Toronto provides ample funding for your home’s backwater valve installation.
Why would you risk the integrity of your home and health, when the city has you covered?
The city of Toronto recently developed a basement flooding protection subsidy program that provides up to $3,400 per property. This covers the installation flood protection gear, including a backwater valve, sump pump, pipe severance, and pipe capping.
The city’s subsidy program covers up to 80% of the invoice, reaching a maximum of $1,250 for the backwater valve installation. The backwater valve installation price is very low when you use a Toronto plumber who is licensed with the city.
7. Anta Plumbing Has Backwater Valve Installation
Are you ready to install a Backwater valve? Do you need help on how to start?
You can’t install a backwater valve on your own. For coverage from the city’s subsidy plan, you need a licensed plumbing company to help you with your backwater valve installation.
We have certified professionals who can ensure your home’s protection from harsh weather. Anta Plumbing provides a competitive backwater valve installation price, a permit for the installation, and guidance with the city’s basement flooding protection subsidy program.
If you’re located in Vaughan, there are different requirements for subsidy eligibility. Make sure you hire a Toronto licensed plumber to install your backwater valve.
Get Started Today
Now that you know the consequences of basement flooding, you should start on your plan to install a backwater valve.
If you found any of these signs in your home and you live in Ontario, connect with our team today!
Anta Plumbing Company is a City of Toronto Licenses Plumbing Company with the best deals on backwater valve installation, sump pump installation, and other plumbing services.
We have locations in Ajax, King City, Toronto, Milton, Hamilton, Oakville, and all throughout Ontario.
Outside faucets are super handy. They’re necessary for gardening projects, and with the temperatures warming up in our area, you don’t want to run inside every time your plants require water. They’re fun for the family, with the help of sprinklers and pools to escape the summer heat. Overall, no home is complete without the addition of an outside faucet for easy access to water.
However, if your outside faucets are running into trouble, they can be very obnoxious to deal with. We’re going to try and do some troubleshooting and give you some explicit directions when it’s finally time to call a plumber in Clifton, NJ.
Don’t panic, outside faucet systems are relatively simple. While they might endure more weathering and problems that come from being outdoors, they’re still a plumbing system. We’ll always be able to help you with your plumbing.
The Problem of Rust
Outside faucets rust more easily than indoor ones. Rust occurs when your metal plumbing appliance comes in contact with water and oxygen, which is plentiful in our atmosphere. Here in New Jersey, we get all four seasons as well, which means your outdoor faucets are also contracting and expanding season after season, icing up, developing cracks, and also rusting.
Sometimes when your outdoor faucet cracks due to ice expanding and rupturing the metal, there’s an increase in exposure to air and water since there’s more surface area of your appliance to rust. Basically, all of these problems work together to make it a harsh environment for your outdoor faucet.
Repairs and Replacement Services
If your outdoor faucet is becoming unusable, that’s not good. It could be due to rust, problems with the physical integrity of the appliance, or more. Here are a few problems you could be running into, and we’ll mention whether or not you need repairs or replacement.
When to Repair Your Outdoor Faucet
Poor water pressure. Water pressure can usually be a problem with your plumbing system itself. Before replacing the whole unit, we’d rather take a look as a plumber to see if we can’t locate the problem and fix it.
Rust-colored water. If you’ve got rusty-colored water coming from your pipe, this could be from built-up sediment, corrosion, rust, or something else. Our team can take a look.
The hose or other attachment is broken. While this might seem like a devastating problem, the fact is that the most exposed parts like hoses and faucet heads are the ones that break first. Your system still might work fine with a new head or hose.
It’s leaking. Leaks happen, and unless they’re in a bad spot, they can be patched up easily.
When to Replace Your Outdoor Faucet
It’s rusted through. If your whole outdoor faucet is rusted through, there are really no repairs we can make that would salvage it. You’re almost always better off with a whole unit replacement.
It’s not providing any water. This often drives a lot of homeowners to forget about their outdoor faucets because they don’t produce water. Unfortunately, then it’s just a waste of space. Call our team to have it replaced.
The professional plumbers at MarGo Plumbing Heating Cooling Inc. have your back. Call us today!
If you’ve heard of slab leaks, then you know that this is a huge issue. Leaks might happen in your home underneath your sink or even in your kitchen, but a slab leak is something that’s going to stop the entire operation of your home. A slab leak can happen to the best of us. If you think that this is something that’s occurring in your home, then it’s important to spot this problem and get a professional out to your home fast.
Our professionals are prepared to handle your slab leak in Orlando, FL. If you’d like to keep your home in impeccable shape, we’re going to be the team on your front lines. We’re going to help you spot a slab leak in your home today.
5 Signs You Might Have a Slab Leak
Here are the signs that you might have a slab leak in your home:
1. Hot Spots
One of the most noticeable signs of a slab leak is hot spots on your floor. If you’re walking around your home and notice that a couple particular spots make your feet feel toasty, it’s actually a problem. Hot spots are a sign that there’s hot water leaking underneath your floorboards. What you’re feeling is the concrete underneath your home getting warm enough to warm your floor. This means things are getting severe and you should schedule an appointment with us.
2. The Sound of Running Water
Do you always hear the sound of running water in your home? Don’t think that this is just a benign, odd occurrence. It’s a problem. The sound of running water is just that. Turn off all the fixtures in your home. If you still hear the sound of water moving around underneath your floors or within your walls, then you have a slab leak.
3. Damaged Flooring
Is your flooring damaged or wet? This is a clear sign of a slab leak. If no one has spilled anything, then it’s a slab leak becoming a mounting issue. We’ll help you work through this.
4. Cracking
Have you noticed cracking in your floors or walls? Cracking is a problem. It’s a symptom of the pressure that a slab leak can put on different parts of your home. Cracking will only worsen with time if you’re not addressing it with care. We’re going to help you with what you need.
Bonus: Doming in your floor. If leaks go on for long enough, it can start to warp your floors, walls, or ceilings. This will manifest as domes.
5. High Water Bills
This is a sign that can be a little more subtle. If you notice that your water bills is climbing up each month, then make sure you take note of this. Water bills that keep creeping up are a sign that something is wrong. If the leaps in price become severe and persistent, then it’s a pretty clear sign that you’re having a slab leak. We’re here to sniff out the problem and help you solve them.
Contact Modern Plumbing Industries, Inc. today to schedule an appointment with our team members.
You don’t want your house to have the smell of a sewer drifting through it, but this can sometimes happen to even the cleanest house because of troubles with the plumbing. If your house has terrible odors making daily life unpleasant, you’ll want to know the source and have it corrected.
Outside faucets are super handy. They’re necessary for gardening projects, and with the temperatures warming up in our area, you don’t want to run inside every time your plants require water. They’re fun for the family, with the help of sprinklers and pools to escape the summer heat. Overall, no home is complete without the addition of an outside faucet for easy access to water.
If you’ve heard of slab leaks, then you know that this is a huge issue. Leaks might happen in your home underneath your sink or even in your kitchen, but a slab leak is something that’s going to stop the entire operation of your home. A slab leak can happen to the best of us. If you think that this is something that’s occurring in your home, then it’s important to spot this problem and get a professional out to your home fast.