A toilet that won’t flush is frustrating, but here’s the good news: It’s probably an easy fix.

Our team of experts at Len The Plumber has put together the following guide to the most common reasons a toilet won’t flush. Depending on the issue with your toilet, you may be able to solve the problem yourself without needing to call a plumber.

The Lift Chain Has Too Much Slack

If you push down the handle and feel no resistance, the lift chain inside the tank, which connects to the flapper and releases water, has probably shifted, resulting in too much slack on the chain.

Solution: Remove the tank lid and shorten the length of the lift chain until there’s no longer slack between the flapper and the handle.

The Toilet Is Clogged

If someone in your family used too much toilet paper, dropped an item like a toy into the bowl, or flushed a sanitary product, a clogged toilet is almost inevitable.

Solution: You might be able to fish out items like toys on the surface. However, for absorbent materials, such as sanitary products or diapers, try to plunge out the clog or use a toilet brush to clear it.

The Water Level Is Low

When there isn’t enough water in the bowl, your toilet can’t flush. The float ball in your tank might have been misadjusted — signaling to your toilet that there is not enough water to flush properly.

Solution: Lift open the tank lid. The float ball should be floating 1 to 2 inches below the overflow tube and fill valve. There might also be a line etched into the porcelain indicating what level the float ball should stay at. Adjust the float ball to remain at that level.

The Flapper Is Warped

If you notice your toilet is running often, the flapper might be warped. The flapper is connected to the lift chain and opens when you press the toilet handle. Over time, a rubber flapper can bend or warp, making it unable to seal the flush tube hole and release water to flush the toilet.

Solution: Purchase a new flapper at a hardware or home improvement store. They are inexpensive and easy to find. Turn off your water main, drain the toilet tank, and replace the warped flapper with the new flapper. Turn your water back on and try flushing the toilet again.

There’s a Drain Line or Sewer Problem

If you’ve tried all of the above fixes and your toilet still won’t flush, it’s probably time to call a professional to check your plumbing and sewer system for major backups. The biggest sign that you have a drain line or sewer system issue is when there are clogged drains throughout your home, not just in your toilet.

Solution: Call a licensed plumber who has the tools and expertise to find clogs without needing to remove pipes. When there’s a drain line or plumbing issue, the problem is no longer something that a DIY solution can fix. Your plumbing professional will probably use video pipe inspection as well as long-reaching augers to make the necessary repairs.

Call Len The Plumber for Plumbing Repairs in the Mid-Atlantic Region

If you live in the Mid-Atlantic region and would rather a professional take a look at your toilet, contact Len The Plumber. Our expert, licensed plumbers have the experience and expertise to provide same day service, seven days a week.

Call Len The Plumber today at (800) 950-4619(800) 950-4619 or contact us online, and we’ll send a certified plumber to fix your toilet as soon as possible.  

This post first appeared on https://lentheplumber.com

The problem with plumbing is that you might not realize when you need certain services. We understand that repiping is one of those jobs that you want to be absolutely certain about before you engage in it. It’s one of those services that has the reputation of being extensive, expensive, and stressful.

We understand that this is the reputation, but it doesn’t always have to be the outcome. We can help you find an Altamonte Springs plumber that is ready to provide you with quality care. If you’re unsure where whether it’s really time to repipe, you’ve found the right blog post. We’ve listed some of the common indicators that it’s time to give your home’s plumbing system a fresh start below. 

A Few Signs That You Should Repipe Your Home

Here are a few signs that your home is ready to be repiped. 

Chronic Low Water Pressure

Have you noticed that there is now low water pressure in your home even though there hasn’t been before? If your water pressure has reduced to a trickle, then it’s definitely time to consider repiping services. 

Visible Corrosion

Your plumbing system is one of those systems in your home that’s largely out of sight and out of mind. This is why we suggest that you peek in your plumbing system and figure out what’s going on from time to time. Have you noticed that your home’s plumbing looks bad? If it has visibly corroded and this is coupled with other signs of plumbing problems, then you should definitely consider new pipes. 

Water Discoloration

Is your home’s water discolored? Your water should always be clear and completely transparent. If you notice that your water is murky, dingy, or any type of color, then we suggest repiping sooner than later. This is typically one of the earlier signs that you’re having a plumbing issue. Don’t let this problem become an ongoing issue. We’ll help you with this. 

Frequent Clogging

Clogs are actually a normal occurrence. We all make mistakes every now and then regarding what can go down a sink or a toilet. Things escalate into a real issue when you start to notice frequent clogging. Frequent clogging is a sign that your pipes have a real issue somewhere. Older pipes made with outdated materials are more likely to run into clogs. If your home is 50 years or older and the pipes have never been replaced, then you should definitely pick up the phone and discuss repiping with one of our pros. 

Leaks

Have you noticed that you’re running into multiple leaks in your home? This isn’t something that you should ever have to worry about. This is especially true if you’re running into leaks often. Leaks are an urgent plumbing issue because they can quickly lead to water damage throughout your home. Although a leak can occur every once in a while, frequent leaks in a home are an indication that your pipes have seen better days. 

Contact Modern Plumbing Industries, Inc. today to schedule an appointment for repiping services. 

This post first appeared on https://www.modernpi.com

Heating systems are so vital, especially during the cold season. At such times, every house needs some degree of heating. Here, the HVAC systems come in handy. It is paramount for you to run your heating system efficiently. You will avoid the system breaking down or consuming too much energy at your cost. Below are tips on how to run your heating in Livingston, NJ.

Changing Air Filters

The system’s air filters keep it free from clogging. They capture the dirt as the air cycles in, along with all the dust. As they gather debris and dirt the air filters are prone to blockage.

Changing the air cleaners will help prevent the system from jamming and slowing down. Additionally, mobbed air vents will force the system to work harder and use more energy. A straining system accelerates the process of wear and tear. Furthermore, such a system consumes more energy. Besides costing you more, you will compromise the quality of incoming air.

Turning on Ceiling Fans

Run your ceiling fans to improve the quality of circulating air. The fans rush up the movement of air around your house. The speedy movement will, in turn, allow you to run your AC cost-effectively and save energy.

Note that heating in Livingston, NJ, will be low-level when the weather is moderate. The humidity will, in turn, be low too.

Adjusting the Thermostat

The heat in your home is dependent on the efficiency of the thermostat. Turn the thermostat back by a few degrees when you do not need more heat. You can save up to 10% on your utility bill.  

Be careful if your thermostat is manual. Remember to adjust the device as you leave. Nevertheless, one of the best ways to improve heating at home is to replace your manual device with an automatic programmable thermostat.

The device will allow you to select and set a heating schedule, save energy automatically, and not worry about forgetting to adjust. These smart thermostats will allow you to change your settings and get updates.

Cover Your Windows

Windows with drapes or covers will help heat your room ahead of the thermostat kicking in at night. These drapes will improve the efficiency of your energy.

Also, think about pulling aside your drapes during the day. Remember that a vast majority of the sunlight falling on double pane widows enters the house to become heat, giving your thermostat a head-start in heating.

Schedule for Maintenance

You will need to keep your heating system effective by maintaining regular check-ups. The maintenance will replace the air filters and ensure that all the air vents are open to your heating system’s efficiency.

Finally, schedule preventive maintenance for your heating system and leave this maintenance to professionals. They will check the calibrating system tasks, check the fluid levels, and clean the interior units.  

Are you trying to fix issues with your heating system so that it runs efficiently? If so, please Contact MarGo Plumbing Heating Cooling Inc. for professional heating services you can count on! We have been in the business for many years and have the experience, techniques, and technologies to repair the heating system.

The post How to Run Your Heating System Efficiently first appeared on MarGo Plumbing Heating Cooling Inc..

This post first appeared on https://margoplumbing.com

Introduction:

How to prepare your plumbing for heavy snow?

With the winter season, there’s a good chance that heavy snowfall will be a common occurrence. This means that it is important to prepare your house for this type of weather, and you’ll want to know how to prepare your plumbing for heavy snow. To do so, one would want to disconnect the hose from the spigot at night or when it’s not being used. You should also make sure that all of your pipes are insulated. If any water lines have frozen over, try thawing them out by running warm water on them or using a hairdryer on low heat before turning back on the household water supply again! Lastly, NEVER turn on the household water supply without first checking for leaks!

Heavy snowfall is expected this winter and it’s important to prepare your home or business’s plumbing for the conditions. If your house is prone to leaks, you may want to make some more permanent improvements before winter hits and definitely find and fix any existing problems as soon as possible. Here are 5 critical ways to prepare your house plumbing for an Ottawa winter:

Relevant: Plumbing Maintenance Checklist For Fall and Winter

1) Turn off the Hose Connection at Night

In severe cold weather, homeowners have been known to leave their garden hoses attached from the spigot to outside faucets that aren’t being used. This allows a constant supply of water into those lines that could freeze if allowed to sit with no power running through them during the night. Always disconnect these hoses from the exterior faucet at night or when they’re not being used.

2) Keep the Pipes Warm

In cold weather, you should always keep your heating system contained in a sunny area and avoid letting walls and exterior insulation block the winter sun from entering all windows. In addition to turning on your heater if it’s cool inside, be sure to cover exposed pipes with insulating foam pipe sleeve covers that have been approved for use with natural gas or propane. You can also try using an indoor-safe heat lamp near where the pipes are located to help warm them up before winter sets in.

3) Check Insulation Levels for Your Outdoor Faucets & Hose Connection

Make sure that your outdoor faucets as well as any hose connection points are covered with ready-to-use outdoor faucet insulation kits. This includes looking for cracks in the connection where water can leak out if it freezes.

4) Thaw Frozen Water Lines

If any of your exterior water lines are frozen or burst, make sure you do not turn on your household water supply again without first checking to see if there’s a leak inside the home. If you suspect that a pipe has burst, shut off the main shutoff valve into your house and then open one cold water tap at a time until you find which one is dripping. Repair this damaged section of pipe before turning your main valve back on. You should also look for wet spots around all joints in exposed pipes to ensure they haven’t become damaged. If any damage is found, shut off your water supply and contact a plumber to service the line.

5) Never Turn On Your Household Water Supply Again Without Checking for Leaks

If you are concerned about preventing pipe damage when turning on your household water supply after winter, it’s best to call in professional plumbing service for an inspection before doing so. A plumber can check all of the valves, inspect lines near all exterior faucets, hose connections, and outdoor spigots to make sure none have been damaged by leaking or freezing throughout the winter weather. They can also help you revise your home’s plumbing system if necessary including adding insulation or installing shutoff valves outside in case pipes freeze again next year. If you have any questions about how to properly winterize your home’s plumbing, please contact a licensed plumber in your area.

Conclusion:

This winter is expected to have heavy snowfall. As a homeowner, you’ll want to be prepared for the 5 critical ways your house needs to prepare for this snowy weather event. Hope you enjoyed this resource!

When everything is running smoothly in your home, it’s easy to forget about the small things that can make a big difference, like when to change a furnace filter. Neglecting this one small step can lead to a variety of issues with your HVAC system. While there are varying schools of thought as to how often should you change your furnace filter, it’s better to err on the side of caution.

If your filters are not clean, that means your system is pumping dirty air throughout your home, increasing the amount of dust and allergens you are breathing into your body. This can manifest itself in physical form via headaches, colds, chest pain, and other allergic reactions. Cleaning your air filter could make you feel a whole lot better.

But how often should you change your furnace filter? Use this guide to learn more about the process and why it is important. 

How often should furnace filters be changed?

According to the International Association of Certified Home Inspectors (InterNACHI), you should change your air filter at least every three months to avoid having any issues in your home and to keep your system running at maximum efficiency.

You can change a furnace filter either by yourself or with the help of a certified, professional heating and cooling provider if you have any further questions about your system.

What about a faster furnace filter replacement time? 

While three months is the standard for how often to replace a furnace filter, your individual circumstances, environment and usage may result in a more accelerated schedule. Some factors that determine how often you should change your filters include:

• The current season’s average temperature. Do you have to run your furnace or air conditioner all day long, or is the temperature outside mild enough to keep the system turned off?
• Is it pollen season for plants or trees in your neighborhood? If your car is coated in yellow powder in the morning, that same substance will soon be coating your home’s air filter.
• Is there construction being done in the area, has the rainfall been especially light, or is there any other reason for more dust to be airborne?

What are some problems that can occur if I don’t replace my filter?

While it may feel like keeping a regular furnace filter change interval is unnecessary, there are some major negatives that can occur if neglected. In addition to the personal affects that may happen, there are these other issues:

• Reduced air flow: HVAC units are designed to have a certain amount of internal airflow, and a dirty air filter reduces the amount of air that gets to you and the system. If you feel as if your home isn’t as warm or as cool as the temperature settings would suggest, the air filter could be the culprit.
• System damage: When filters become clogged with air, it can lead to lead to a pressure drop that doesn’t allow any air infiltration at all. In addition, a filter exposed to condensation can become moldy. Both issues can have serious consequences for your HVAC system and could lead to costly repairs or a full replacement of the unit.
• Increased electric bills: A dirty air filter will cause your system to work harder in order to get to your desired temperature, which in turn, causes a spike in power. The U.S. Department of Energy says that replacing a dirty, clogged filter with a clean one can lower your air conditioner’s energy consumption by 5 percent to 15 percent.

How to tell if your filter is working

• Make a habit of checking your air filter once a month to see if it’s clogged. If you see a gray or yellow ashy substance filling the fibers in the filter, it’s time to change it for a fresh, clean one.
• If you’ve gone three months without the filter getting clogged, and you’ve used it on a regular basis during this time, check the filter to see if you’ve got the right size. The wrong size of filter can allow air to pass between the filter edges and the wall of the HVAC duct, reducing the efficiency of your filter system.

Another element to consider when thinking about how often to change the furnace filter is the filter itself. The lowest-priced item is not always the best value. Cheap filters, usually sold as loss leaders in a big box or hardware stores, trap a few of the contaminants you want to keep out.

For the best combination of efficiency and cost-effectiveness, as a homeowner, you should stick with the highest-rated pleated or polyester fiber air filters you can find, with a minimum efficiency reporting value (MERV) between 7 and 13, according to the Environmental Protection Agency. They’ll keep the air in your home clean and healthy while avoiding the high costs of more expensive filters that do more than you need.

The post How often should you change your furnace filter? appeared first on Stahl Plumbing, Heating & Air Conditioning.

Most people tend to use the terms boiler and furnace to mean the same thing; however, they are two different ways to heat your home, with distinct differences in how they work. Whatever type of unit you may have, it’s important to use a qualified, fully licensed professional to help you service your system on a regular basis.

When it comes to the boiler vs. furnace argument, this guide will focus on how a boiler works and what you need to do to ensure your boiler works effectively and efficiently.

What’s a boiler?

Let’s clear up the terms first. A furnace runs on heat, whether it’s gas, electric, or propane, that runs through the home. It then sends the hot air in vents using the home’s duct system for heating.

On the other hand, water is the key element for a boiler heater. The boiler system distributes heat created from boiled water or steam through hot water pipes. The heat comes out of either baseboards or radiators. While most boilers use hot water or steam, there are boiler systems that use gas, oil, or even wood to create warmth.

What does a boiler heating system look like?

Water boilers are generally tall and cylindrical shaped. They are almost always found in basements or garages due to regulations that require them to be installed along a house wall. Installation and maintenance of your boiler can be tricky, so it’s best to leave that to well-trained, professional HVAC companies.

How does a boiler work?

The science behind boiler operation is relatively simple. When you turn on your system, a gas boiler will heat the water in the tank using a flame. An electric boiler’s coils or other heating element will activate to heat the water. The warm air is then driven upward through the pipes to its eventual endpoint – the baseboards or radiators. This is called the radiant heat transfer method.

What are the pros of a boiler system?

There are several important benefits to consider when thinking about how a boiler works and whether you want to install a new system or retain your home’s existing system.

• Energy savings: For the most part, boilers are a better bargain because they use less fuel to heat the home.
• Less maintenance: Boilers don’t use filters, so you don’t have to worry about switching out filters every three months.
• Consistency: The heat produced by the boiler is more consistent and equitable throughout the home. With a furnace, some rooms may be hotter than others.
• Less noise: Boilers are usually quieter than furnaces because they don’t have the sound of hot air blowing throughout the house.
• Cleaner air: Because boiler systems don’t blow air, the potential for dust and allergens to spread throughout your house is reduced.

What are the cons of a boiler system?

While boilers do provide several optimal qualities, it is important to understand that there are some drawbacks to this form of heating.

• Harder installation/conversion: The process of installing a boiler is harder than a furnace; plus, switching from a boiler to a furnace can cost- and labor-prohibitive.
• No cooling: Boilers can’t produce cool air, so if you live where central air is key to your comfort, they aren’t the best option.
• Slow reaction time: When you change the temperature on your boiler, it can take a while for the process to work. In other words, it’s not for the impatient.
• Leak dangers: When a boiler goes belly up, it can cause major leakage in your home. Most boilers are located in basements partially for this reason, but you shouldn’t have anything valuable near your boiler.

How does radiator heat work?

Radiators stationed throughout a home act as the disbursal points for the boiler. The heat is pushed up to the radiators, which then emit the heat in the room. Most radiators have a knob on the side to modulate the amount of heat that comes off the unit. If you turn it fully open, the room will receive the maximum amount of heat.

Radiators also can become blocked with air, preventing the heat from escaping. You can use a special radiator key to bleed the radiator, releasing air and water to ensure it works properly when you turn it on again.

What does a boiler do regarding energy production?

A boiler’s efficiency level is noted by its annual fuel utilization efficiency (AFUE) measure. The government requires newer boilers to display this number to show how the appliance converts energy from fuel to heat over the course of a year. According to the Department of Energy, those who live in cold climates should have boiler systems with a 90% to 98.5 percent AFUE.

If you have an older boiler system and want to update it through retrofitting, reach out to your local, knowledgeable HVAC provider, who will have options about the best steps to take next.

The post How does a boiler system work? Boilers vs. furnaces appeared first on Stahl Plumbing, Heating & Air Conditioning.

The Sequencer: A Key Part of Your Electric Furnace

The post The Sequencer: A Key Part of Your Electric Furnace appeared first on Cool Touch Air Conditioning & Heating.

This post first appeared on https://www.thetrustedplumber.com

When we talk about water heaters with our homeowners, we’re often surprised by the way they think of it. If you’re taking your water heater for granted, we want today to be the last day you do so. Your home’s water heater is one of the hardest working and most important systems that you have in your home. This is because you use your water heater daily and heavily. It’s the system you’re relying on to take a shower, wash your dishes, and wash your clothes. If you need great water heater service in Peoria, AZ, then understanding your water heater is a great place to start. 

Today, we want to make the subject of your water heater knowledge start with the anode rod. If you have a tank water heater in your home, the anode rod is essential for the function of the system. 

What’s an Anode Rod?

An anode rod is a rod made of magnesium and zinc housed in the tank water heater. The reason that magnesium is used in this system is because magnesium breaks down much faster than steel does, especially when in contact with zinc. You need a magnesium rod breaking down inside of your tank because your water heater tank is made of steel. Without the magnesium rod inside of your tank, the steel of the tank would break down and corrode in no time. 

If you talk to professionals about an anode rod, you might hear it referred to as a “sacrificial anode rod.” This is because an anode rod breaks down to better benefit your home’s water heater. It’s necessary for the overall function of your system.

The Genius of Water Heater Manufacturers

Most things that are exposed to water long enough will eventually break down. Although your water heater has one job and it’s to heat up your home’s water, this isn’t something that’s going to be feasible without the right protection. The people who manufacture tank water heaters understand this. Your water heater is typically full of certain chemicals over time. This is when the anode rod needs to go to work.

The anode rod is the unit that hits back at any corrosive elements sitting in your home’s water heater system. The anode rod consumes corrosive elements like steel. This can occur in your home’s water heater over time as the unit corrodes from age. The anode rod keeps your system balanced. 

What Professional Service Does for You

Now that you know the ins and outs of your water heater and the anode rod specifically, we want to leave you with our most important note—professional service is required. Don’t think that you can sidestep professional care when you need repair work or any maintenance care. Professional service is important because we’re the only ones who have the training necessary to keep your water heater in good working condition. 

Our plumbers are ones that you can always rely on for quality service. We make sure that the service we provide is as prompt as it is high quality. 

Contact The Trusted Plumber today to schedule an appointment with our professionals. 

This post first appeared on https://www.thetrustedplumber.com

A sudden spate of rainy weather can flood streets and neighbourhoods. However, flooding can also leave unprepared homeowners facing a foul-smelling menace. In a worst-case scenario, you might face basement flooding from sewage overflow!

To avoid potentially facing stiff repair costs on your own, you should make sure your home has a backwater valve. A sewer backup valve isn’t something that every house has, however.

If you’re unsure, we can help. Read on for a guide on backwater valves and how to see if you have one.

What Is a Backwater Valve And What Does it Do?

A backwater valve is a backflow prevention device meant to prevent basement flooding.

A backwater valve allows water to drain from a house while preventing wastewater from coming back up your pipes.

Backwater valves activate when your municipal sewers can’t handle any more waste. For example, this keeps sewage from being pushed back through your fixtures in a flooding scenario.

Inside the valve is a “flap” that allows draining water to flow freely. If water comes from the opposite direction, this flap is pushed close. The flap will re-open once the water recedes.

Where To Look For a Backwater Valve

A sewer backup valve will typically be housed in your basement, close to your sewer line. Older homes are less likely to have one. Newer homes may have been built with one or retrofitted with one. It is generally a good idea to check regardless of your home’s age.

In your basement, you can start searching for the valve near your sump pump. It will usually be close by.

If your basement is cluttered, you may need to move things around. If you happen to find your valve beneath clutter, consider reorganizing your basement.

Covering your backwater valve makes it difficult to check water levels. Additionally, it makes maintenance more time-consuming.

The backwater valve will typically be mounted into the floor. Usually, it has a clear plastic case so you can see inside. If it is opaque, you may remove the cap to peer inside (though exercise caution in doing so).

If you notice water flowing freely, your flap is down and allowing water to drain. If the compartment appears to be filling or is full, the flap has activated. It isn’t recommended to open the cap in this case.

Do I Need a Backwater Valve If I Don’t Have One?

It is generally recommended that you have a backwater valve if you are a homeowner. Not only are backwater valves useful in stopping flooding, but insurance companies also tend to view your home as less of a risk with one.

In municipalities where flooding is more common, you may find that your insurer requires you to have a backwater valve. Some municipal governments offer rebates for having them installed, however.

Lacking a backwater valve can cause damage to the structure of your home over time.

If your basement is consistently damp and has crack-filled walls, you may need a backwater valve. Consistent flooding and moisture can cause mould and mildew that can damage your home.

There are other signs that you may need a sewer backup valve as well.

If you need a backwater valve, it is best to find a plumber to assist. Retrofitting existing plumbing is a tricky procedure that is best left to professionals.

The risks of an improper backwater valve installation are reasonably high. From flooding to wastewater contamination, it’s just not worth it!

Basic Backwater Valve Maintenance

Having a backwater valve installed may require professional assistance, but luckily, maintaining one is an easy DIY job.

Regular DIY maintenance can ensure that your backwater valve functions properly and will reduce the frequency of clogs and breakdowns.

Before conducting any maintenance, make sure to don protective gear! Wastewater is chock full of contaminants that can make you very ill. Gloves and eyewear are a must, but a face mask is also recommended.

Try running hot soapy water down a drain to help clean your plumbing lines a bit before you start working. Alternatively, you can flush the valve itself with water.

Open the cap and inspect the interior of the chamber for obstructions.

If there is any debris or buildup, take care to remove it, so it does not accumulate. This is especially vital around the flap, as it can become stuck and won’t deploy in a flood. Use a brush to scrub the chamber clear of any sewage buildup; you may need to remove debris with your hands.

Make sure to periodically inspect replaceable components such as the floats on the flap or o-rings sealing pipes.

Of course, prevention is the best method when it comes to maintenance.

Pay close attention to what goes down your pipes. Thicker materials such as paper towels can clog your lines and interfere with a backwater valve. Even “toilet safe” wipes may occasionally build up in a valve.

Ensure to inspect the valve to check for any debris periodically. If you find it consistently, you may need to stop using that product.

As with any plumbing issue, remember that there is only so much you can do before consulting a plumber. Your home’s pipes and fixtures are delicate and improper maintenance can be costly!

Need A Backwater Valve Installed?

A backwater valve is a vital piece of plumbing that can prevent backup problems. Without one, your home risks a foul basement flood!

If you’re in the Toronto area, Anta Plumbing can get your house the sewer backup valve it needs. Locally owned and licensed, we know our neighbourhood and its needs well. We can even work with you to get a rebate on installation!

The post How To Tell if You Have a Backwater Valve first appeared on Anta Plumbing Blog. This post first appeared on https://blog.antaplumbing.com

According to a study done at the University of Scranton, of the 45% of people who make New Year’s resolution, only 8% successfully achieve their goals. While this number is quite low, we’re encouraging all of our customers (new and old) to at least consider our New Year’s resolutions. This year we hope you consider the following resolutions:

1. Be nicer to your garbage disposal.
This year, try to make a more conscious effort about what you’re throwing down your disposal. Here’s a great reference to see what you should and shouldn’t put down your disposal.

2. Give your water heater a little T.L.C.
Just like the oil in your car, your water heater needs regular maintenance as well. Our technicians will ensure your system is running properly by flushing the system making sure to get rid of any buildup or sediment.

3. Save Water.
If you’re in the market for a new toilet, consider installing low-flush toilets. This will save you water and money on your next water bill.

4. Keep your pipes warm.
Winter temperatures can affect your pipes. Make sure they’re properly insulated to avoid pipes bursting in your home. Follow these important tips to winterize your plumbing!

5. Get your home’s plumbing system inspected.
When we’re in your home, you’re entitled to a free home plumbing inspection. While some people decline this service, we encourage you to allow our technician to make sure everything is in good working order. You never know when that hidden leak could start costing you a lot of money!

6. Fix plumbing issues sooner rather than later. 
Keep your eyes and ears open for leaks, drips, noisy water heaters, running toilets etc.

This year, we hope that you’ll make your first resolution to get a hold of us as soon as you think you have an issue with your plumbing.

Waiting until it’s too late to fix a plumbing problem can be a costly headache. Since we’re here for you 365 days out of the year and don’t charge extra for service on weekends and holidays, give us a call at any time!

This post first appeared on https://lentheplumber.com