Your sump pump may fail due to one of these three problems
Introduction:
Sump pumps are an important part of keeping your home safe from flooding. If your sump pump fails, it can cause serious damage to your home and belongings. In this article, we will discuss the three most common problems that can cause a sump pump to fail: An Overworked Sump Pump, Blockage, and Poor Installation.
We will also give you tips on how to fix each of these problems so that your sump pump will be up and running again in no time!
Call Us at (877) 959-3534 for Plumbing Service
Major Causes of Sump Pump Failure
1. What is a Sump Pump and why do I need one?
A sump pump is a pump that is installed on the lowest level of your home, typically in the basement. The purpose of a sump pump is to remove water that has accumulated in the sump pit and to prevent flooding. Sump pumps are usually activated by a float switch, which turns the pump on when the water level in the sump pit rises to a certain point.
2. The three most common problems that can cause a sump pump to fail
A Sump Pump That is Overworked
Some sump pumps are better than others. If you buy a cost-effective plastic model, you are at a greater risk of burnout. You might have a higher-quality pump, but sometimes only one is not enough to handle a high volume of water.
It is advisable to invest in a high-capacity sump pump, which will get you out of most situations when you need it most. If your system isn’t strong enough, you should have a battery-powered backup on hand.
Call Us at (877) 959-3534 for Plumbing Service
Blockage
Dirt and dust will accumulate in lidless sump pumps over time, eventually clogging the pump. Your system will either perform poorly or will not function at all if you do this. A clean system is necessary to prevent a blockage from making a bad situation worse, so you should have your system checked annually. It is important to get a technician out as soon as possible if you notice anything wrong with your sump pump.
Poor Installation
Your sump pump will work best if you hire the right installation team. It is possible that your system may not be there for you in your time of need if you hire a company that does not follow the manufacturer’s instructions. This could cause severe water damage. By hiring a reputable company with a guarantee of quality work, licensing, and insurance, you can prevent this problem.
3. How to fix a clogged sump pump
If your sump pump is clogged, the first thing you should do is check the inlet screen. The inlet screen is located where the water enters the sump pit. If the inlet screen is clogged, it will prevent water from entering the sump pit and cause the sump pump to run continuously. To clean the inlet screen, simply remove it and rinse it off with a hose.
If the inlet screen is not the problem, then the next thing you should check is the impeller. The impeller is located inside the sump pump and helps to move water through the pump. If the impeller is clogged, it will prevent water from being pumped out of the sump pit and cause the sump pump to run continuously. To clean the impeller, simply remove it and rinse it off with a hose.
If the impeller is not the problem, then the next thing you should check is the discharge pipe. The discharge pipe is located where the water exits the sump pit. If the discharge pipe is clogged, it will prevent water from being pumped out of the sump pit and cause the sump pump to run continuously. To clean the discharge pipe, simply remove it and rinse it off with a hose.
Conclusion:
It is important to know how to address the three most common problems that can cause a sump pump to fail-clogs, power outages, and broken motors. In this article, we have given you tips on how to fix each of these problems so that your sump pump will be up and running again in no time!
Summer is almost here. Although it’s not officially summer on the calendar quite yet, the weather might have had you fooled. It’s hot out there and when the temperatures start to rise, it’s easy for the focus in your home to become air conditioning, air conditioning, and more air conditioning.

Everyone’s first thought when they hear this is likely going to be about a clog. Grab the plunger and get to work! However, clogs are only one of many reasons a toilet may fail to flush. Today we are going to look at a few more reasons why our favorite plumbing fixture could experience difficulty.
How to unclog a “moderately clogged” drain
The SeeSnake Mini video inspection system
offers a reliable solution in a ruggedized package. The Mini is also available with a durable self-leveling camera head. This tool is Ideal for where portability and maneuverability are crucial: multi-story buildings, rooftops, confined areas, etc. It has many great features. The self-leveling camera head delivers crisp, clear, always upright in-pipe images. The built-in 512 Hz Sonde allows you to locate a point of interest during a pipe inspection. The push cable pushes farther, and it takes a wide range of lateral and mainline applications.
Alternatively, you can use the SeeSnake® CS10 Digital Recording Monitor. The CS10 Monitor combines RIDGID® durability with the easiest to use digital recording monitor in the plumbing industry.
One touch recording allows you to record snapshots and video directly to a USB stick then hand it directly to your customer.



