Seven Simple Tips on How to Fix a Leaky Faucet

Seven Simple Tips on How to Fix a Leaky Faucet

6 Simple Steps to Repair a Leaky Faucet

A leaky faucet often indicates a problem with one of the parts being worn out. How you go about repairing the faucet depends on where it drips and the mechanical makeup of your faucet. You have four main types of faucets that will depend on compression, disc, cartridge, and mechanism.

Before you attempt to fix a leaky faucet, you should first determine the type of faucet to understand how you go about fixing it. Here are some of the tools you will need before starting:

If you have a widespread faucet there are usually decorative covers over the valves. Most times there is a fine thread on the valve assembly so attempt to unscrew the trim piece. ÿBeneath each knob, you will find a screw that mounts the handle to the stem. You will unscrew the handle and gently remove the handle. Sometimes the faucet handle will not come off the stem easily. Spray the WD-40 on this part to loosen it.

After you have loosened the packing nut, you should see the stem. You want to take this part off all. At this point, different faucets will diverge in how you deal with them. For example, you have some stems that pop off while others will twist from the valve. Remove everything gently. You want to skip over the possibility of damaging the parts because this could exasperate a leaky faucet problem.

If your faucet is under 25 years old it has a cartridge. After turning it on and off for 25 years the seats are probably worn out. Attempt to pull the cartridge straight out using a set of channel locks pliers. Sometimes these cartridges are tough to remove because scale has built up and locked them in place. Give the cartridge a slight wiggle while pulling and it should eventually work itself out. If you can?t remove call a plumbing professional. There are cartridge removal tools available.

Replacement washers and O-rings.

Replacement washers and O-rings.
Adjustable wrench.
Philips screwdriver.
WD-40.

O-ring.

Stem.

O-ring.
Stem.
Packing nut.
Screw.
Handle.

At this point, everything should remain together. Look at the washer and the O-ring inside of the valve seat. Many times, this part causes leaks when damaged, or the seal starts to wear off. You will remove the washer and replace it with the new washer.

You will also want to replace the O-ring because many times this component experiences damage. Before replacing your O-rings and washers, first, check to see if it fits right. When unsure of either, look at the seat to check if the sides will fit with the flat washer. You may have to buy a more appropriate size.

For those with problems finding the right sized O-ring, instead, take it to the hardware store to get an exact fit. For those unsure about this, check the seat and see if the sides will fit the cone shape. Then you can buy the appropriate O-ring. Instead of taking an old O-ring to the hardware store, you can also opt out of that to buy a variety of different sized O-rings in a package. It does cost a couple of extra bucks, but it will be worth every penny to get the size needed.

Once you have the parts, you will need to reassemble them. It will be done in this order when putting it back together:

Tips and Troubleshooting

After you have taken apart and reassembled your faucet, you will want to check to see the faucet no longer drips. If it does, the cause could be deeper than a busted O-ring. In many cases, the next possibility lies in corrosion with the valve seat.

This happens when it remains dirty over time and eventually produces a leak closer to the spout of the faucet. If that fails to fix your leaky faucet, other potential problems include loose parts, worn-out seals or broken plumbing. If you have tried these things without success, it might be time to hire the big guns and call a plumber.

Putting It All Together

When this happens, you will have to identify where the water enters the home to shut it off. Keep in mind, when you shut off the water valve, an entire residence will cry out for the lack of water. Nevertheless, it sometimes becomes necessary during a repair.

This post first appeared on http://www.theplumbinginfo.com

Leave a Reply

Your email address will not be published. Required fields are marked *

This website nor its owners are an actual service provider, this website is a referral service. When you place a phone call from this website, it will route you to a licensed, professional service provider that serves your area. This website may receive compensation for referrals. For more information refer to our terms of service.

© PlumbingRepairServiceUSA.com

(877) 959-3534